Today we have a 2005 Ford Focus 2.0l brought in with the complaint the battery light is on. Let's try to diagnose what the problem is together and get this car back on the road. Tools Used: Autel MaxiSYS MS909: Snap-on Zeus Precision Low Amp Probe 0:00 Intro 0:30 Scanning For Codes 3:32 I Spy The Alternator 4:09 Charging The Car 4:40 Looking At Live Data 6:00 Load Testing The Battery With A Carbon Pile Tester 7:21 Testing The Alternator With An Oscilloscope 9:55 Testing The New Alternator With An Oscilloscope

Today we are going to try to create a universal flip key for a 2009 Mazda 6. Tools Used: Xhorse Key Tool Max XHORSE VVDI VOLKSWAGEN B5 TYPE UNIVERSAL REMOTE KEY 3 BUTTONS BLACK - WIRED FLIP KEY ROLL PIN VICE TOOL 0:00 Intro 0:30 Trying To add a Fob Using Emulation 2:09 Connecting The Key Tool Max To A Wired Remote 4:00 Cloning The Transponder 4:50 Assembling The Key 5:58 Testing The Fob 6:25 Roll Pin Installing Clamp 6:44 Testing The Keys and Programming The 3rd Key

Today We Have a 2006 BMW 530xi All Keys Lost. We are going to add a smart key and cut the emergency key. Tools Used: im508 Autel MaxiIM Maxi Bundle ORIGINAL LISHI HU92 BMW SINGLE LIFTER 2-TRACK 2-IN-1 PICK - IGNITION/D XHORSE CONDOR DOLPHIN XP-005 KEY CUTTING MACHINE AUTOMATIC 0:00 Intro 0:30 1:11 Connecting To The Car 1:55 Programming The New Key 3:15 Testing The New Smart Key 4:00 Getting The Key Cut Code 4:26 Cutting The Emergency Key 7:34 Testing The Emergency Key

Today we have a 2010 Chevrolet Cobalt 2.2l with a 5 speed manual transmission that has a check engine light on. Let's see if we can figure out what is going on and get this car back on the road. Codes: DTC P0446 -Evaporative Emission (EVAP) Vent System Performance DTC P0452 -Fuel Tank Pressure (FTP) Sensor Circuit Low Voltage Tools Used: Thinkdiag2 All System Bidirectional Control OBD2 Diagnostic Scanner for iOS & Android, Bluetooth5.0 Intelligent Scan Tool with CAN-FD Protocol, AutoVIN, Active Test, 15+ Reset Functions, ECU Coding ESCAN Elite Snap-on Zeus 0:00 Intro 0:30 Scanning For Codes 1:40 Looking At Live Data and Sealing Fuel Tank 3:06 Visual Inspection... Uh Oh 4:05 Fixed Wiring 4:30 Checking Live Data and Bidirectionally Controlling The Evap System 7:00 Bidirectionally Controlling The Vent Valve 7:32 Bidirectionally Controlling The Purge Valve 9:50 Removing The Fuel Cap 10:22 Oopsie 10:45 Testing The System Again 13:48 Looking At Mode 6 With Escan 16:20 Using The Zeus To See What Codes Did Not Run 22:00 Coolant Temperature Dropping 25:23 Checking Our Monitors and Mode 6 Data 17:30 Looking At Code Testing Criteria

Today we have a 2003 Ford Explorer 4.0l Sohc 4x4 with the complaint that it is stuck in the snow and the four wheel drive is not working. Lets see if we can figure it out together. This was tough, I did not have many tools with me and it was in snow and ice on a hill next to parked cars. Tools Used: Launch x431 Pro Mini 3.0: 0:00 Intro 0:30 Full System Scan 1:40 Looking At Live Data 3:30 Bidirectionally Controlling The Transfer Case 5:16 We Have 4WD LOW 12:18 We Have 4WD High 13:44 No Lights On Switch 14:25 Checking Fuses 15:00 Switch Not Plugged In? 15:37 Confirming Fix

Today we are going to try to unlock a BMW 5WK49127 Smart Key. This is also called renewing. This is when you make the remote blank like it was brand new. Tools Used : Xhorse VVDI Key Tool MAX Remote Generator - KEY TOOL MAX ONLY 0:00 Intro 2:30 Opening The Smart Key 3:22 Soldered The Wires On 5:08 Removed The Battery 5:55 Unlocking THe Smart Key 6:57 Testing The Smart Key

Today we have a 2002 Chevrolet Trailblazer 4.2l 4x4 that has a Service 4WD message on the dash and the 4WD does not work. Let's see if we can figure out what is going on with this vehicle. Codes: u1000 - Critical Operating Parameter Has Not Been Associated C0374 - Unable To Correct Sensed Wheel Slip C0379 - Front Axle Control Circuit Short To Ground, Short To Voltage, Or An Open Circuit C0550 - Critical Operational Parameters Stored In EEPROM Have Failed, Checksum Error Tools Used: Launch x431 Pro Mini 3.0 Snap-on Zeus CarDAQ Plus 3 0:00 Intro 0:30 Code Scan 4:30 Looking At Live Data 7:00 Bidirectionally Controlling The Transfer Case 10:00 Turning The 4WD Light On 10:50 Trying To Control The Front Differential Lock 12:30 Looking In Repair Information At The TSB For C0550 13:35 Following The TSB And Removing The Fuse 15:10 Checking For Changes 16:08 Checking Wiring Diagrams 17:24 Bidirectionally Controlling The Transfer case Motor 19:58 New Dorman 599-113 Transfer case Module 20:50 New Module Installed 21:56 Scanning For Codes 23:36 Trying To Control The New Module 26:16 Reprogramming The Transfer Case Module With SPS 35:14 Testing To See If Reprogramming Worked! 36:26 Test Driving The Vehicle 38:06 Scanning For Codes!

Today we have a 2016 Kia Rio That the customer lost all the keys for and we are going to pick, decode, and cut a key for the car off the door lock cylinder. This car does not use transponders so the key will work in the ignition if it works in the door lock. Tools Used: Original Lishi HY22 KIA7 KK10 2-Track 6-Cut Hyundai Kia 2-in-1 Xhorse VVDI Key Tool Plus Programmer - Advanced Version Xhorse Condor DOLPHIN XP-005 Key Cutting Machine Automatic Training Vise Lock Holder Clamp For Original Lishi Tools https://keyinnovations.com/products/t... 0:00 Intro 0:30 Picking With an HY22 Lishi 3:30 Decoding The Lock 6:50 Unpicking The Lock 8:15 Checking The Key Bitting 10:30 Cutting The Key 17:20 Testing The Key Out

Today we have a 2006 Nissan Altima that the customer said we had to learn the key. They said the car will not start and the immobilizer light is on. Codes: P1610 - Lock Mode P1614 - Chain Of IMMU-KEY Tools Used: im508 Autel MaxiIM Maxi Bundle Xhorse VVDI Key Tool MAX Remote Generator - KEY TOOL MAX ONLY 0:00 Intro 0:30 Manual Identifying The Vehicle 1:21 Scanning Vehicle For Codes 3:18 Trying To Learn A Key 4:58 Using Key Tool Max To Test Key 6:02 Testing Coil With Key Tool Max 6:37 We Found Our Issue 7:17 Adding Keys After New Coil Installed 8:45 Showing NATS Antenna Amplifier 9:10 Testing Both Keys

Today we have a 2011 Chevrolet Cruze that we need to cut and program some spare keys for with remotes. Follow along as we try to do this. 0:00 Intro 0:30 Breaking In 0:55 Decoding The Key 2:26 Cutting The Key 5:00 Trying The Key 6:11 Trying To Clone The Transponder 9:50 Generating Remote 14:39 Adding A Key Using IM508 19:30 Looking At The FCC ID 19:55 Generating A New Key 20:44 Trying To Add Our New Key Again 23:11 Trying Our New Keys